* WIP: Advanced commands for portisch firmware
* Fix string code sending
* clang formatting
* Add new rf_bridge functions to test
* Add advanced code received trigger
* Fix copy-paste mistake in the advanced sending
* Fix log message to be consistent
* clang
* Remove extra +
* fix: FastLED SPI_DATA_RATE being truncated to 8 bits
FastLED expects SPI_DATA_RATE as an uint32_t, but we had it as uint8_t.
Fix that to avoid the data rate being truncated.
* fastled: allow specifying data rate
Previously, we've just taken the default data rate from FastLED.
However, that does not always work properly. In my case, I had a
slow level shifter that couldn't keep up with the 1 MHz data
rate default for WS2801. Long cabling might also be a reason why
one might want to reduce the data rate.
This will add a new optional "data_rate" config option where one
may specify the desired data rate as a frequency:
light:
- platform: fastled_spi
chipset: WS2801
data_pin: GPIO23
clock_pin: GPIO22
data_rate: 500kHz
num_leds: 178
* Started to work on packages feature
* Added some more validation to packages config
* Fixed some linter warnings
* Updated tests
* Reordered consts to avoid linter error
* Reordered consts to avoid linter error
* Refactored test yaml files to integrate into existing test pipeline
Co-authored-by: Dmitry Berezovsky <dmitry.berezovsky@logicify.com>
* Start support for tuya climate devices
* Add tuya climate to test4
* Fix lint and cast
* Remove blank line
* Try to display accurate action based on observed behaviour.
* Fix action when in off mode
* Improve config dump
* merge use of CONF_SWITCH_DATAPOINT
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* TFT-LCD ST7789V of ESP32 TTGO.
This patch allows you to use TFT-LCD ST7789V of ESP32 TTGO
* Lots of polish and a few tweaks
* Add test
* Add color to core, take 1
* Where did those tabs come from?
* Fix lines too long
* Added color component
* Linted
* Rebase, SPI fix, test
* Shuffle bits
* One more thing...oops
* Image type fix...oops
* Make display_buffer use Color
* Fix BGR/RGB, remove predefined colors
* Fix all the things
* renamed colors to color
* migrate max7219
Co-authored-by: musk95 <musk95@naver.com>
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* Add fan support to bang bang controller
* Fix heat-only and cool-only modes
* Added support for all climate actions and modes
* Fix up some comments
* Fan_only mode behavior tweak
* Updated test
* Updated test, take 2
* Add accessor methods for easier use in lambadas
* Revert "Add accessor methods for easier use in lambadas"
This reverts commit f15713129cd5587242a08ad1e2ee37cbf075aa03.
Don't code late at night when sleepy.
* Fix single/dual setpoint support
* Linted
* Properly implement single-point, validation improvements
* Another quick fix...sigh
* Update tests
* Update tests, take 2
* Revert "Update tests, take 2"
This reverts commit 71bb7fccc53d95a7d221e80ea0a931fb3cfd9a0c.
Nope.
* Revert "Update tests"
This reverts commit 42044291efaaf09858f29ab27bbc3aa9e8b80ee9.
Nope 2.
* Updated/fixed tests
* Revert "Updated/fixed tests"
This reverts commit a1a5b1c7db9a240b9da668b6e48abe1dd7910777.
Taking a different approach.
* Revert "Another quick fix...sigh"
This reverts commit 6b1955724a2de3c2d1534ec206dd5794bbb5f568.
Taking a different approach.
* Revert "Properly implement single-point, validation improvements"
This reverts commit f5bfff099e1dc58edd3898da8655c147adde2301.
Taking a different approach.
* Single/dual set point fixes, full validation
* Fix test
* Fix restore-on-boot, clean up comments
* Decouple two-point/auto operation, more polish
* One last away mode tweak
* Added set point validation
* Clean up over-publishing, always call action after boot
* Add fan support to bang bang controller
* Fix heat-only and cool-only modes
* Added support for all climate actions and modes
* Fix up some comments
* Fan_only mode behavior tweak
* Updated test
* Updated test, take 2
* Add accessor methods for easier use in lambadas
* Revert "Add accessor methods for easier use in lambadas"
This reverts commit f15713129cd5587242a08ad1e2ee37cbf075aa03.
Don't code late at night when sleepy.
* Fix single/dual setpoint support
* Linted
* Properly implement single-point, validation improvements
* Another quick fix...sigh
* Update tests
* Update tests, take 2
* Revert "Update tests, take 2"
This reverts commit 71bb7fccc53d95a7d221e80ea0a931fb3cfd9a0c.
Nope.
* Revert "Update tests"
This reverts commit 42044291efaaf09858f29ab27bbc3aa9e8b80ee9.
Nope 2.
* Updated/fixed tests
* Revert "Updated/fixed tests"
This reverts commit a1a5b1c7db9a240b9da668b6e48abe1dd7910777.
Taking a different approach.
* Revert "Another quick fix...sigh"
This reverts commit 6b1955724a2de3c2d1534ec206dd5794bbb5f568.
Taking a different approach.
* Revert "Properly implement single-point, validation improvements"
This reverts commit f5bfff099e1dc58edd3898da8655c147adde2301.
Taking a different approach.
* Single/dual set point fixes, full validation
* Fix test
* Fix restore-on-boot, clean up comments
* Decouple two-point/auto operation, more polish
* One last away mode tweak
* Added set point validation
* Clean up over-publishing, always call action after boot
* Added refresh() function to allow easy on-device state refreshing
* Fix fan oscillation trait not being used
* Add fan direction support to SpeedFan
* Add fan direction to API
* Add fan direction support to BinaryFan
* Fix CI errors
* Fix python format
* Change some ordering to trigger CI
* Add test for the configuration
* Extend `uart:` with `rx_buffer_size:`
This allows to configure `rx_buffer_size:`
to efficiently receive big payloads over UART
* lint
* remove old default value
* add test
Co-authored-by: Guillermo Ruffino <glm.net@gmail.com>
* esp32_ble_tracker: introduce UUID comparison function
* ble_presence, ble_rssi: use new UUID comparison function
* esp32_ble_tracker: introduce automation on BLE advertising
* test2.yaml: remove deep_sleep due to firmware size restrictions
* add energy support in pzemac sensor
Co-authored-by: Sergio Mayoral Martinez <sergiomayoralmartinez@gmail.com>
Co-authored-by: t151602 <sergio.mayoralmartinez@telefonica.com>
Co-authored-by: Otto Winter <otto@otto-winter.com>
* add new config options
* init variables in code
* load css and js in python
* update print inside webserver
* fix indentation
* fix indentation
* indentation fix
* fix condition in init
* use cv.file_ instead of cv.string
* do not import EsphomeError
* support embedding js and css at the same time as defined in url
* handle css as separate page
* handle js as separate page
* fix copy and paste error
* Add support for Sensirion SPS30 Particulate Matter sensors
* Remove blocking of the main thread on initialization;
Improve wording on the debug messages;
Add robustness in re-initialization of reconnected or replaced sensors;
* Fix code formatting;
Co-authored-by: Nad <valordk@github>
* implemented ruuvi_ble and ruuvitag with RAWv1 protocol
fixesesphome/feature-requests#313
* lint
* updated data calculations
* cpp lint
* use string directly in message
Co-Authored-By: Otto Winter <otto@otto-winter.com>
* add RAWv2 protocol support
* fix ICON_SIGNAL
* typo
* calculation correction and cleaning
* c++ lint
* added acceleration and fixed typo
* removed remote_receiver to reduce firmware size
remote_receiver also in test1.yaml
* Add MAX31865 sensor support, fix MAX31855 sensor.
# MAX31865
Added support for the MAX31865 RTD-to-Digital Converter to measure PT100 and
similar RTDs. Verified with an Adafruit unit (product ID: 3328) and a PT100
probe.
# MAX31855
This was setup for incorrect SPI clock polarity and phase, and would return bad
data due to a race condition measuring on the wrong edge (verified with Saleae
Logic scope). Selecting the correct configuration fixes that problem.
Re-wrote the decode off the datasheet to handle error states better (sends NaN
as an update on failure to read temperature, which shows the value as Unknown
in Home Assistant).
Added the *optional* ability to monitor the internal high-precision temperature
sensor, which can be nice in some applications.
* Tests for MAX31855/MAX38165.
* Update style to match project rules.
Also fix CONF_REFERENCE_RESISTANCE and CONF_REFERENCE_TEMPERATURE being defined
multiple places. Missed this when I added them to const.py.
* Update style to match project rules.
Pylint line limit 101/100 ("missed it by that much").
Also apparently I can't read and patched the wrong line in max31855.cpp.
* Minor string/style cleanup.
There was a copy-paste leftover in max31855.cpp and max31865/sensor.py had
unnecessary whitespace.
* Improve MAX31865 fault detection and logging.
Log levels are more in-line with the documented descriptions.
Fault detection code is improved. A transient fault between reads is still
reported, but now only faults *during* a read cause the sensor to fail and
return NAN ("unknown" in Home Assistant).
* Update style to match project rules.
I just now realized the .clang-format and pylintrc files are included. D'oh!
* MAX31855 & MAX31865 code style alignment.
@OttoWinter caught some style mismatches, updated to match project better.
* Fix a lost '\' in max31865/sensor.py.
